Do You Think Fiat Panda Key Fob Replacement Ever Rule The World?
replacement key fiat 500 with the fiat 500 number is a convenient method to open the doors and start the car. However, there are a variety of reasons why the fob won't be functioning. This includes a dead coin-battery, water damage, problems with the receiver modules, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason the 500 key fob won't function is the battery is dead. Modern key fobs only have limited operating range and must be within a few inches of the vehicle in order to work. If you're far from your vehicle and press the key fob button, the car won't respond, and will display an "Key Fob Not Detected" message in the instrument cluster.
If this occurs, replace the coin-cell battery (Part Number CR2032) by a new one of a trusted brand like Panasonic Duracell or Energizer. You can usually find them at your local hardware store or on the internet.
You can test the battery of your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The car should blink its parking lights and the key fob should work the lock and unlock buttons.
If the fob's key doesn't function after replacing the battery, it might be damaged by water, which prevents it from connecting to the receiver module in your car. Water damage can occur in a variety of ways, such as the simple splash or submerging the key fob in saltwater at the beach. If you think your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work your fob will probably require reprogramming by an experienced auto locksmith or dealer.
Water Damage
Although the fob is equipped with rubber seals that keep water out of the chip's electronic circuit, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater poses a particular risk to the fob's circuit board, causing it to short out and eventually die. It's not the best idea to submerge the fob in water but don't give up in the event that you accidentally drop it in water, or fail to take it out of your pants pocket.
First remove the battery from the fob. Clean the electronic chip using isopropyl ethanol or a similar product and then dry it thoroughly before replacing the battery. Test the fob next to verify if it's functioning. If the key doesn't function, it may need to be reset. This is usually handled by an auto locksmith or dealer.
If your key is older and not programmed for your car You will need to replace it completely. This is a simple process which can be accomplished by a professional automotive locksmith. The locksmith will require the key to be cut to match the car's ignition. They will also need to reprogram the fob for your vehicle's system. This is a fast and cost-effective process that can be completed on the same day.
Receiver Module Issues
Your 500 key fob might not work because it's out of range. The remote has a maximum range of 30 feet. Therefore, if you are too far from your vehicle it will not respond to your commands. You can easily solve this issue by moving the remote closer to your car until it responds.
If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work it could be due to an internal circuit board issue. In the majority of cases, reprogramming your fob will fix the issue. You can find the steps for most vehicles on YouTube or in the owner's guide.
You may need to replace the metal retaining clips that hold the coin battery. If they lose tension, it could prevent the battery from sitting properly, and this will result in the malfunction of your remote.
In rare cases the fob could be out of sync with your vehicle because due to hardware or software issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances the software may require reinstallation in your body control modules.
Interference
Interference can also cause the key fob to not be able to receive or transmit signals. This could occur if the key fob is near the radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob may not function due to a poor connection with the buttons or water damage, or damage to the internal chips.
If the key fob failed to work one day without notice or after trying everything you can at home to solve it e.g. replacing batteries, reprogramming or using the spare key fob, it could have a faulty receiver module on your 500. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key fob. It converts the signals into electronic commands that are then processed by the vehicle.
Fortunately, there's an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any remaining electricity and restart the car's computers. This could allow you to the key fob to function again. If the issue persists, you should consult an expert technician. They'll be able determine the exact cause of your problems.